shovelhd
Autocross Champion
- Location
- Western MA
Way too hot. Trims hitting 47 and lots of timing pull. What kind of fuel are you using?
I'd back it down at least 1psi from 3K up, then run it again.
7
JB4 Logging, stacking and Map 6 Discussion
- Thread starter George Smooth
- Start date
Way too hot. Trims hitting 47 and lots of timing pull. What kind of fuel are you using?
I'd back it down at least 1psi from 3K up, then run it again.
shovelhd
Autocross Champion
- Location
- Western MA
It's a little bit hot. We are in fuel changeover season in the Northeast. Keep an eye on it.
NBMK7GTI
Go Kart Newbie
- Location
- Putnam County, NY
“93 octane”. How much timing pull wasthere?
One cylinder knocked once after spool up. It's really not terrible. Try logging the this Map 4 on another road. Do like 3 logs if possible and post it up.
I would be more conserned with how lean it is.
https://datazap.me/u/adiroma/75-r-3-log-map-4-11-17-20?log=0&data=1-4-18
NBMK7GTI
Go Kart Newbie
- Location
- Putnam County, NY
you think changing fol would help?
Probably because your trims are up around 40. Raise it another 10 and log again.
Thanks for the messages. I am running Tesco momentum 99 (which is 98 RON) -
I will try a different map and post with results again soon.
Hello, is this a good log? Tried map 2 on 91 for the first time. 2018 GTI SE all stock besides the jb4.
https://datazap.me/u/figlin/map-2?log=0&data=1-4
https://datazap.me/u/figlin/map-2?log=0&data=1-4
chewbacca.be
New member
- Location
- Belgium
- Car(s)
- Leon ST Cupra 4drive
Hello there,
I'm new with JB4 and I'd like to have some advice for customizing a map6. I bought my unit second hand so I don't have the direct support from Burger Tuning.
Here is my current setup : leon cupra st 2019 4drive with GPF; remus OPF back; K&N panel air filter, currently running map4 with 98RON.
I did a log in map 2 (attached) I don't know where to start from there.
Thanks in advance
Pierre
I'm new with JB4 and I'd like to have some advice for customizing a map6. I bought my unit second hand so I don't have the direct support from Burger Tuning.
Here is my current setup : leon cupra st 2019 4drive with GPF; remus OPF back; K&N panel air filter, currently running map4 with 98RON.
I did a log in map 2 (attached) I don't know where to start from there.
Thanks in advance
Pierre
Hey Pierre! Saw you found your way here 
Please create a free account at datazap.me and upload your logs there, much easier for the gurus here to analyze them:
https://datazap.me/
Just post a link to the logs here afterwards.
Please create a free account at datazap.me and upload your logs there, much easier for the gurus here to analyze them:
https://datazap.me/
Just post a link to the logs here afterwards.
chewbacca.be
New member
- Location
- Belgium
- Car(s)
- Leon ST Cupra 4drive
Can you please post the Map 4 log also?
chewbacca.be
New member
- Location
- Belgium
- Car(s)
- Leon ST Cupra 4drive
Of course,
Here you are : https://datazap.me/u/chewbaccabe/log-1606408856?log=0&data=1-4
The map4 pull were logged with release firmware, the MAP2 pull with the Alpha (don't know if this is important)
Here you are : https://datazap.me/u/chewbaccabe/log-1606408856?log=0&data=1-4
The map4 pull were logged with release firmware, the MAP2 pull with the Alpha (don't know if this is important)
Map 4 is too aggressive for your fuel. We can work a Map 6 off your Map 2 values.
1. Click this link: https://datazap.me/u/chewbaccabe/log-1606407014?log=0&data=1-3-4
2. Run your cursor across and note the 2500, 3000, 3500, 4000, etc TARGET values.
3. Enter those recorded values in to your Map 6 cells.
4. For 1500, and 2000, you can enter "2", for 7000 you can enter "5".
5. Switch your JB4 to Map 6 and run a log.
You should get a similar result to your Map 2 log. If it looks good, we can start tweaking.