gc9n
Ready to race!
- Location
- None (International)
Sign asssit is not working , because i didnt find the time to calibrate the camera
Yea from infotainmemt system there is a tick box for Light Asssit On off
7
Retrofitting Lane assist camera without changing windshield?
- Thread starter Reaper1
- Start date
Sign asssit is not working , because i didnt find the time to calibrate the camera
Yea from infotainmemt system there is a tick box for Light Asssit On off
So how can you get light assist to work?
And i was talking about sign assist, in the infotainment it is called dynamic road sign display.
Sent from my SM-G955F using Tapatalk
gc9n
Ready to race!
- Location
- None (International)
i dont know , i just didnt get back any error , didnt test it, i can anbale it from the lever with no error , i see the icon on the dash
Yea Road Sign, and Head Light assist are avaliable from the Infor.
Oh, so its just calibration. The rest looks good
As for me, i think i know what offset the camera is talking about.
When i was going through the liva data for my camera i saw 3 offset channels for each axis, and one of them looks pretty bad.
And how can i know if 2.5 degrees on pitch is 2.5 down or up?
Piot if you are reading this, is it possible that you give us your reading from those 3 channels?
Sent from my SM-G955F using Tapatalk
Last edited:
gc9n
Ready to race!
- Location
- None (International)
The calibration was unsuccessful.
The reason for this is: Installation position incorrect
Note:
An incorrect installation position of the front camera was detected
- Check the front camera for correct installation and correct detected errors
VAS6430 is not printed as it sould , i have to reprint it
The reason for this is: Installation position incorrect
Note:
An incorrect installation position of the front camera was detected
- Check the front camera for correct installation and correct detected errors
VAS6430 is not printed as it sould , i have to reprint it
hmm, are you sure the camera can see the entire board? and that it is flush against the windshield?
gc9n
Ready to race!
- Location
- None (International)
my board is cropped from the bottom , the guy printed this 1 month ago made this mistake. might be this
Attachments
-
2019-01-19_14-33-32.jpg
The camera doesnt camera about the white edges, it needs to see only till the black edges.
gc9n
Ready to race!
- Location
- None (International)
the board is fine ?
this is the camera,
so you mean that the camera housing it self (not the bracket) have to be 90Degrees flat as its positioned into te glass?
this is the camera,
so you mean that the camera housing it self (not the bracket) have to be 90Degrees flat as its positioned into te glass?
Attachments
-
2019-01-19_14-47-47.jpg -
2019-01-19_14-47-37.jpg -
2019-01-19_14-47-24.jpg -
2019-01-19_14-47-11.jpg
It looks fine.
The OEM Camera heater is flush with the glass which keeps the camera in the correct angle aswell, are the both flush?
gc9n
Ready to race!
- Location
- None (International)
the board black columns hieght have to be 96,0cm or 960mm ,
mine is 80cm or 800mm
both flush , as i understand..
How is possible to be so clever, there might be a electronic lever inside the camera
mine is 80cm or 800mm
both flush , as i understand..
How is possible to be so clever, there might be a electronic lever inside the camera
hmm,thats weird.
He didnt print it in the correct dimensions.
Did you use the file from piots site?
gc9n
Ready to race!
- Location
- None (International)
Yea his printer was small to the edge,
Monday morning I get a glossy better one
Monday morning I get a glossy better one
Im sure you can find a better place, and get it laminated so no dust or water can damage it.
gc9n
Ready to race!
- Location
- None (International)
i hope that message is misleading , rather than true!
because i saw cameras hanging with ducttape from windsceeen and calibrated after that!!
because i saw cameras hanging with ducttape from windsceeen and calibrated after that!!