GOLFMK8
GOLFMK7
GOLFMK6
GOLFMKV

Search results

  1. jawndropper

    FS: 19x8.5 +35 Rotiform RSE in Philly area

    Imgur album with photos 1 wheel is curbed (wheel #4 in the pictures). The other 3 are in decent shape with some nics and scratches from 2 years of daily driving. These wheels use the stock mk7 wheel bolts. $500 OBO Sold for $450
  2. jawndropper

    P0413 code

    Coming back to say that I replaced the sai pump and sensor in April and haven’t had an issue since.
  3. jawndropper

    P0413 code

    I bought a new SAI combo valve back in January and took my car to a shop to have replaced. They disconnected the plug and found it was covered in soot. They cleaned the connector and told me to wait and see. No issues for 6 or 7 weeks and then out of nowhere it came back today 😭. I already...
  4. jawndropper

    Daks' GTI

    hard to tell without a better shot. never seen those before. TSW Sebring is kind of similar with the 5 Y spokes ontop and 2 spokes going straight through each Y. Doubt you'll find anything with that color combo though. and by the time you get another set painted it might just be cheaper to get...
  5. jawndropper

    What did you do to your mk7 today?

    Finally got an alignment after installing Eurosport camber mounts and 034 dynamic control arms about 500 miles ago. Ready to hit the track this weekend. still have a lot of room for adjustment upfront if I want.
  6. jawndropper

    What did you do to your mk7 today?

    Swapped to the summer setup for the track this weekend. Put on a fresh set of Falken 615ks and scrubbed my rpf1s the best I could. Not even 20minutes after I finished, it started snowing….
  7. jawndropper

    What did you do to your mk7 today?

    I ran the NGK rs7 plugs for about 50,000 miles/ at 5-10k intervals without issue. Just wanted the extra piece of mind. 🤷‍♂️
  8. jawndropper

    What did you do to your mk7 today?

    Installed Apr spark plugs 😭🤣 read enough horror stories about the rs7 plugs and made the switch.
  9. jawndropper

    2017 GTI Sport - $$$OLD

    How much did you get?
  10. jawndropper

    3D Printer & C.A.D. Thread

    i used fusion 360, the logo is recessed into the plate. I still can push/pull the logo but when I zero it out the border is still there, I cant seem to actually delete the logo. 🤷‍♂️
  11. jawndropper

    3D Printer & C.A.D. Thread

    Coinslot cover is done. Still not perfect, but I am pretty happy with this. I wanted to make a second blank version but I cant figure out how to remove the logo now lol. https://www.thingiverse.com/thing:5847754
  12. jawndropper

    What did you get in the mail or bring home for your MKVII today?

    Oil Zimmerman drilled rotors Ferrodo ds2500 Rbf600 Apr spark plugs 🤣 Oem Front end links H&r 24mm rsb Moog rear end links (no magnet from rock auto?) Jack pad kit from Eacca fresh set of Falken 615k+ Last but not least a new rear wiper It’s going to be a busy weekend.
  13. jawndropper

    What did you do to your mk7 today?

    I had eurosport camber mounts and the new 034 control arms installed today. I previously had 034 strut mounts and bearings for about 40,000 miles and had been experiencing clunks for quite some time now. My stock control arm bushings were shot aswell (75,000 miles). I haven't gotten an alignment...
  14. jawndropper

    3D Printer & C.A.D. Thread

    measure once, print and revise 13 times 🤣 - now i can appreciate CJM charging $15 plus shipping lol Finally got all the dimensions right and the cutout in the right spot. Tried adding a VW logo, it seemed to work fine. Now I need to dial in the printer and get some black filament.
  15. jawndropper

    3D Printer & C.A.D. Thread

    i absolutely suck at CAD but am making progress with the coin slot cover :ROFLMAO: fortunately these only take about 45 minutes to print. Not sure where to start diagnosing why my circles arent printing right
  16. jawndropper

    3D Printer & C.A.D. Thread

    I am trying to recreate a coin slot cover. I've never used CAD before but I whipped this up in 30 minutes last night. The design is far from perfect and I have some printer issues to work out but I am off to a good start. Once I figure out what Im doing in Fusion 360, I will post the STL...
  17. jawndropper

    What did you get in the mail or bring home for your MKVII today?

    I got a load of parts delivered today in prep for upcoming track season. 1. the newly released 034 motorsport control arms 2. eurosport camber mounts (pre-assembled) 3. Strut mount hardware kit from FCP. 4. control arm hardware kit from shopdap. 5. new SAI pump, gasket, and sensor from FCP. I...
  18. jawndropper

    3D Printer & C.A.D. Thread

    my new monitor's vesa mounts are too recessed to fit my monitor arm. Thankfully there is a solution for everything on thingiverse.
  19. jawndropper

    BNIB Aerofab V2 Diffuser MK7 GTI.

    60 day bump
  20. jawndropper

    P0413 code

    Well it lasted about 11 days and the CEL came Back. Got the usual P041300 and a new P049100 - SAI system Insufficent flow. I am going to suck it up and have the combi valve replaced next week.
Top