Search results

I bought a new SAI combo valve back in January and took my car to a shop to have replaced. They disconnected the plug and found it was covered in soot. They cleaned the connector and told me to wait and see. No issues for 6 or 7 weeks and then out of nowhere it came back today 😭. I already...

hard to tell without a better shot. never seen those before. TSW Sebring is kind of similar with the 5 Y spokes ontop and 2 spokes going straight through each Y. Doubt you'll find anything with that color combo though. and by the time you get another set painted it might just be cheaper to get...

Finally got an alignment after installing Eurosport camber mounts and 034 dynamic control arms about 500 miles ago. Ready to hit the track this weekend. still have a lot of room for adjustment upfront if I want.

Swapped to the summer setup for the track this weekend. Put on a fresh set of Falken 615ks and scrubbed my rpf1s the best I could. Not even 20minutes after I finished, it started snowing….

I ran the NGK rs7 plugs for about 50,000 miles/ at 5-10k intervals without issue. Just wanted the extra piece of mind. 🤷‍♂️

Installed Apr spark plugs 😭🤣 read enough horror stories about the rs7 plugs and made the switch.

How much did you get?

i used fusion 360, the logo is recessed into the plate. I still can push/pull the logo but when I zero it out the border is still there, I cant seem to actually delete the logo. 🤷‍♂️

Coinslot cover is done. Still not perfect, but I am pretty happy with this. I wanted to make a second blank version but I cant figure out how to remove the logo now lol. https://www.thingiverse.com/thing:5847754

Oil Zimmerman drilled rotors Ferrodo ds2500 Rbf600 Apr spark plugs 🤣 Oem Front end links H&r 24mm rsb Moog rear end links (no magnet from rock auto?) Jack pad kit from Eacca fresh set of Falken 615k+ Last but not least a new rear wiper It’s going to be a busy weekend.

I had eurosport camber mounts and the new 034 control arms installed today. I previously had 034 strut mounts and bearings for about 40,000 miles and had been experiencing clunks for quite some time now. My stock control arm bushings were shot aswell (75,000 miles). I haven't gotten an alignment...

measure once, print and revise 13 times 🤣 - now i can appreciate CJM charging $15 plus shipping lol Finally got all the dimensions right and the cutout in the right spot. Tried adding a VW logo, it seemed to work fine. Now I need to dial in the printer and get some black filament.

i absolutely suck at CAD but am making progress with the coin slot cover :ROFLMAO: fortunately these only take about 45 minutes to print. Not sure where to start diagnosing why my circles arent printing right

I am trying to recreate a coin slot cover. I've never used CAD before but I whipped this up in 30 minutes last night. The design is far from perfect and I have some printer issues to work out but I am off to a good start. Once I figure out what Im doing in Fusion 360, I will post the STL...

I got a load of parts delivered today in prep for upcoming track season. 1. the newly released 034 motorsport control arms 2. eurosport camber mounts (pre-assembled) 3. Strut mount hardware kit from FCP. 4. control arm hardware kit from shopdap. 5. new SAI pump, gasket, and sensor from FCP. I...

my new monitor's vesa mounts are too recessed to fit my monitor arm. Thankfully there is a solution for everything on thingiverse.

60 day bump

Well it lasted about 11 days and the CEL came Back. Got the usual P041300 and a new P049100 - SAI system Insufficent flow. I am going to suck it up and have the combi valve replaced next week.

My car has 75,000 miles. I installed KW v1 coilovers about 40,000 miles ago. Suspension is otherwise stock. I have been abusing the suspension pretty hard over the course of about 30 track days. I want to refresh some stuff to prepare for the coming season and especially sort out my uneven tire...

went to ikea.