GOLFMK8
GOLFMK7
GOLFMK6
GOLFMKV

Search results

  1. railroader

    Mk7 dragy times, 60-130, 1/8, 1/4,

    I know the stock intake is hurting it, I don't and one will help, I don't believe it will make as great of difference as your did, but will definitely help,
  2. railroader

    Mk7 dragy times, 60-130, 1/8, 1/4,

    Here is a customers A3 full weight fbo mpi e60 xl turbo stock air intake, xl is maxed out at around 33psi, shit 4300DA, solid time though
  3. railroader

    Mk7 dragy times, 60-130, 1/8, 1/4,

    Very nice
  4. railroader

    Walbro or Brushless?

    This made me laugh this morning, most people have probably never seen a q-jet, or know that Timing was ever set via distributer or or ever seen a distributor or know what one is, adjusting the points with a dwell meter. Motor tech has spoiled us lol
  5. railroader

    Walbro or Brushless?

    Do it. Only way to learn is to do it, it's not hard and if you run into ossue I or we can help you
  6. railroader

    Walbro or Brushless?

    99.9999% of issues with the pr kit or any other walbro kit is install, you can get them pre installed so it is just drop in also, plug n play, you pay 12-1400 for an rs3 pump that's good for approximately 600whp, 535 with pm4 will cost just under 1k if you get pm4 used and install the pump...
  7. railroader

    Walbro or Brushless?

    Stage 4 pr kit doesn't require a pm4, flows more than an rs3 pump and also cheaper considering everything you get with the kit. It is the best flowing kit for the price. The 535 pump with a pm4 and fuel line will flow just about as much as an rs3 pump
  8. railroader

    Give up on Eurodyne?

    Basic lambda vs di
  9. railroader

    Give up on Eurodyne?

    Also you can make all the same power as any other tuning company out there, especially eqt, nothing magic or special about them except spending tons of money, to be told you have a restriction or something and Check engine lights, that's Cobb as a whole.
  10. railroader

    Give up on Eurodyne?

    For maestro you will have to load the loader files, then the maestro base file off the server, you can download that base file from the server then edit it in maestro editor then flash it
  11. railroader

    TPC Performance Housing Turbo Thread (Not the IS38 Ball Bearing thread....)

    I think the tpc25 would spool better than the rx500,
  12. railroader

    TPC Performance Housing Turbo Thread (Not the IS38 Ball Bearing thread....)

    I have tuned an rx550, it was a good turbo no real complaints, it was in a 4-6k DA area so was laggy,, the.tpc25 will respond better I'm sure of it and will make same if not more power than the rx500, there rx is a solid turbo I just feel as someone who has tuned an rx as well as the tpc feel...
  13. railroader

    TPC Performance Housing Turbo Thread (Not the IS38 Ball Bearing thread....)

    The Vortex turbos have had issues lately and it mostly seams to be with the latest few shipments, an idea of how the qc was lacking was when they "eqt" had a rebuilt turbo they were sending me returned to them enroute cause they had found out that the manufacture may have mislabeled xl and...
  14. railroader

    TPC Performance Housing Turbo Thread (Not the IS38 Ball Bearing thread....)

    Let me put a microphone in the engine compartment for ya lol. I will try and get something, been working on the car installing a few more goodies and mishimoto heat exchangers for.the dsg
  15. railroader

    TPC Performance Housing Turbo Thread (Not the IS38 Ball Bearing thread....)

    I have had both turbos, had an Vortex since they came out, moved to the xl housing when it came out now with tpc770, the xl was good but I will say these new spec tpc turbos are great, my tpc makes target boost faster than my xl did, it also controls boost better, holds boost better and doesn't...
  16. railroader

    TPC Performance Housing Turbo Thread (Not the IS38 Ball Bearing thread....)

    Here is a tpc25 on e61 I'm doing, 6mt gti this is 3rd gear pull, spool is great on these things, making 30psi at 3600rpm and running 34psi up top at 59% wg duty cycle.
  17. railroader

    Mk7 dragy times, 60-130, 1/8, 1/4,

    Wg should be closed for spool up
Top