GOLFMK8
GOLFMK7
GOLFMK6
GOLFMKV

Anyone fitted a highline reversing camera?

E

ericek565

Ready to race!
Location
Slovakia
Car(s)
Mk 7 Variant 2.0
Oh, that is weird because the PDF that it came with had, i quote :

"10 Park assist: Long Coding ->byte2 > BIT4-5 - 10 Camera type: rear view camera (RVC) instaled"
I only knew that you dont enable the (lowline camera in 5F)

The camera is Parametrizied. it does not have "00000000"

Basicaly here is what i´ve connected the camera. With VCDS 1. Added camera in Can Gateway instalation list.
2 .6C Module apeared ( I can do output tests) It wont let me change anything in long coding.
3. 10 Park assist changed long coding to RVC instaled.
4. Adaptations 5F ....BAP_VPS activated
....BAP_VPS_MSG_BUS Databus infotaiment
5. Restarted the radio
 
IWMTom

IWMTom

Autocross Newbie
Location
North East England
ericek565 said:
Oh, that is weird because the PDF that it came with had, i quote :

"10 Park assist: Long Coding ->byte2 > BIT4-5 - 10 Camera type: rear view camera (RVC) instaled"
I only knew that you dont enable the (lowline camera in 5F)

The camera is Parametrizied. it does not have "00000000"

Basicaly here is what i´ve connected the camera. With VCDS 1. Added camera in Can Gateway instalation list.
2 .6C Module apeared ( I can do output tests) It wont let me change anything in long coding.
3. 10 Park assist changed long coding to RVC instaled.
4. Adaptations 5F ....BAP_VPS activated
....BAP_VPS_MSG_BUS Databus infotaiment
5. Restarted the radio
Click to expand...
Sorry, no, you're completely correct. It's been a while since I carried out this retrofit and I was indeed confusing it with the RVC coding in 5F.

You absolutely do need to code in Park Assist module.

Can you please share a VCDS Auto Scan?
 
E

ericek565

Ready to race!
Location
Slovakia
Car(s)
Mk 7 Variant 2.0
IWMTom said:
Sorry, no, you're completely correct. It's been a while since I carried out this retrofit and I was indeed confusing it with the RVC coding in 5F.

You absolutely do need to code in Park Assist module.

Can you please share a VCDS Auto Scan?
Click to expand...
I’m not currently in the Car but this was the only error that camera had. The seccond error is the same.
I currently can work with only this info..

What i found..
If i code in 5F (lowline camera) and put the Car in reverse it shows the black camera screen. If i then manualy open the camera with output test it opens and I can see the camera feed.
There is no other way how can I open the camera.
 

Attachments

  • 4274347E-146B-4506-AF93-7880156AD944.jpeg
    4274347E-146B-4506-AF93-7880156AD944.jpeg
    5.7 MB · Views: 416
IWMTom

IWMTom

Autocross Newbie
Location
North East England
ericek565 said:
I’m not currently in the Car but this was the only error that camera had. The seccond error is the same.
I currently can work with only this info..

What i found..
If i code in 5F (lowline camera) and put the Car in reverse it shows the black camera screen. If i then manualy open the camera with output test it opens and I can see the camera feed.
There is no other way how can I open the camera.
Click to expand...
Is your copy of VCDS legitimate?
 
E

ericek565

Ready to race!
Location
Slovakia
Car(s)
Mk 7 Variant 2.0
It was "original" when i bought it. Turned out it was a clone I mean it costed like 50€. So i use it mostly for me and friends when we need something quick.
So ok I can accept that. Thank you for your help anyways..
 
Fraysa

Fraysa

Go Kart Champion
Location
Israel
Car(s)
2016 MK7 1.4TSI
IWMTom said:
I refuse to assist any further on that basis. The guys at RossTech do not deserve to be stolen from.

Purchase a legitimate interface and register to the RossTech forum, verify your purchase, and then I'll be prepared to help further.
Click to expand...

I completely agree. I think a genuine HexNet interface is a hell of a good deal for 200$ for what it's worth. The guys at Ross-Tech are really putting hard work into it.

What people don't get when they buy a clone is that if we, as customers, won't purchase genuine products, then one day they will just stop manufacturing this. The least we can do is buy an original genuine interface to pay them back.
 
E

ejje

New member
Location
Sweden
Car(s)
MK7 2016 1.2TSI
Hi,

I just installed a highline camera and the installation went fine but its not working 100%...

I have coded according to below and I have image and can switch between camera modes.
But now I have the issue that no guide lines are displayed at all and the parking sensors overlay are not available. EDIT: went for a short drive and now parking sensor overlay is working, but still no guidelines.

I also get following errors:
The rear camera module, gives error: Databus missing message.
Parking assist and airbag gives error: Databus error value received
steering assistance, gives error: "Steering angle sensor- not initialized"
gateway - gives error: Additional installations detected

Does anyone have any idea? My car has parking sensors front and back if that matters.

Please let me know if more info or pictures is needed.

Coding from: http://ilovecarmods.com/vw/composition-media-mib2
Module: 5F (Information electronics)
Coding → Long Coding → Byte: 19 → Bit: 4
New value: disable

Module: 5F (Information electronics)
Adaptation → Channel: Car Function List BAP Gen2 - VPS_0x0B
New value: activated

Module: 5F (Information electronics)
Adaptation → Channel: Car Function List BAP Gen2 - VPS_0x0B_msg_bus
New value: Comfort data bus

Module: 76 (Parking aid)
Coding → Long Coding → Byte: 02 → Bit: 4
New value: enable

Module: 19 (CAN getaway)
Adaptation → Channel: Installation list; specified installations - Camera System Rear View
New value: Coded

Module: 6C (Rear view camera)
Coding → Long Coding → Byte: 07 → Bit: 0
New value: enable

Module: 6C (Rear view camera)
Coding → Long Coding → Byte: 07 → Bit: 1
New value: enable

Module: 6C (Rear view camera)
Coding → Long Coding → Byte: 07 → Bit: 2
New value: enable

Module: 6C (Rear view camera)
Coding → Long Coding → Byte: 07 → Bit: 4
New value: enable
 
Last edited:
DV52

DV52

Drag Racing Champion
Location
Australia
@ejje : hmm......... too much information missing to be precise about the cause of the problem (could be lots of reasons) !! Perhpa best place to start is for you to post-up FULL listing of the long-code string on the new hex 6C module. I'm concerned about the Steering angle sensor fault - you will need to deal with this by completing a Basic Setting procedure (I suspect)

Don
 
E

ejje

New member
Location
Sweden
Car(s)
MK7 2016 1.2TSI
DV52 said:
@ejje : hmm......... too much information missing to be precise about the cause of the problem (could be lots of reasons) !! Perhpa best place to start is for you to post-up FULL listing of the long-code string on the new hex 6C module. I'm concerned about the Steering angle sensor fault - you will need to deal with this by completing a Basic Setting procedure (I suspect)

Don
Click to expand...
Thanks for pointing me in a starting direction. Oh.. not good, guess i need to learn how to do that also then.

6c listing below. If it's any help the camera comes from an golf estate but carsystems.pl was kind enough to answer me that only the angle of the drain hose is different from the hatchback model.

6C Rear View Camera

System description: RVC Compact+
Software number: 5Q0980568A
Software version: 0180
Hardware number: 5Q0980568A
Hardware version: H07
ODX name: EV_CamSysRVRVCARPANAMQBAB
ODX version: 006008
Long coding: 0173020163002017000048

Trouble codes:
U112100 - Databus missing message
static
Date: 2021-05-01 00:22:22
Mileage: 63232 km
Priority: 6
Malfunction frequency counter: 1
Unlearning counter: 236
ARA_error_bits: 0
---: 0.0000 s
Reason: Environmental conditions
current likeliness: 0.0000
---: Passive
U112100 - Databus missing message
static
Date: 2021-05-01 00:22:22
Mileage: 63232 km
Priority: 6
Malfunction frequency counter: 1
Unlearning counter: 236
ARA_error_bits: 0
---: 0.0000 s
Reason: Environmental conditions
current likeliness: 0.0000
---: Passive
U112100 - Databus missing message
static
Date: 2021-05-01 00:22:22
Mileage: 63232 km
Priority: 6
Malfunction frequency counter: 1
Unlearning counter: 236
ARA_error_bits: 0
---: 0.0000 s
Reason: Environmental conditions
current likeliness: 0.0000
---: Passive
U112100 - Databus missing message
static
Date: 2021-05-01 00:22:21
Mileage: 63232 km
Priority: 6
Malfunction frequency counter: 1
Unlearning counter: 236
ARA_error_bits: 0
---: 0.0000 s
Reason: Environmental conditions
current likeliness: 0.0000
---: Passive
 
E

ejje

New member
Location
Sweden
Car(s)
MK7 2016 1.2TSI
Update:

All trouble codes except the databus related ones is gone after som driving. Still no guidelines.

Does anyone have any idea what I can try?

The remaining codes:

6C Rear View Camera

System description: RVC Compact+
Software number: 5Q0980568A
Software version: 0180
Hardware number: 5Q0980568A
Hardware version: H07
ODX name: EV_CamSysRVRVCARPANAMQBAB
ODX version: 006008
Long coding: 0173020163002017000048

Trouble codes:
U112100 - Databus missing message
static
Date: 2021-05-01 00:34:41
Mileage: 63235 km
Priority: 6
Malfunction frequency counter: 1
Unlearning counter: 238
ARA_error_bits: 0
---: 0.0000 s
Reason: Environmental conditions
current likeliness: 0.0000
---: Passive
U112100 - Databus missing message
static
Date: 2021-05-01 00:34:41
Mileage: 63235 km
Priority: 6
Malfunction frequency counter: 1
Unlearning counter: 238
ARA_error_bits: 0
---: 0.0000 s
Reason: Environmental conditions
current likeliness: 0.0000
---: Passive
U112100 - Databus missing message
static
Date: 2021-05-01 00:34:41
Mileage: 63235 km
Priority: 6
Malfunction frequency counter: 1
Unlearning counter: 238
ARA_error_bits: 0
---: 0.0000 s
Reason: Environmental conditions
current likeliness: 0.0000
---: Passive
U112100 - Databus missing message
static
Date: 2021-05-01 00:34:40
Mileage: 63235 km
Priority: 6
Malfunction frequency counter: 1
Unlearning counter: 238
ARA_error_bits: 0
---: 0.0000 s
Reason: Environmental conditions
current likeliness: 0.0000
---: Passive


---------------------------------------------------------------
76 Parking Assistance

System description: PARKHILFE 8K
Software number: 5Q0919294K
Software version: 0054
Hardware number: 5Q0919294A
Hardware version: H03
Serial number: 39391607803968
ODX name: EV_EPHVA18AU3700000
ODX version: 002026
Long coding: 0071151001

Trouble codes:
U112300 - Databus error value received
Intermittent
Date: 2021-05-01 00:04:34
Mileage: 63232 km
Priority: 6
Malfunction frequency counter: 8
Unlearning counter: 23
 
You must log in or register to reply here.
Top