GOLFMK8
GOLFMK7
GOLFMK6
GOLFMKV

DIY MIB1 to MIB2 Infotainment Conversion (Part 1)

SargeMKVI

Semper Fi!
Location
Port St.Lucie
Car(s)
2010 GTI
Ok, so Ive been lurking this thread for a while now. I purchased the 8" DP with the MIB2 brain and usb on my 2015. I have a Fender equipped MK7.

Eurozone sent me an email saying you can make the MIB1 amp work with MIB2 equipment by doing this. Im going to attempt it when my stuff comes in. Here is what they said....

Enabling sound on 2015 vehicles with MIB1 and Fender Audio:
In module 47 in VCDS
1. Plug in VCDS - choose Module 47
2. Choose CODING.
3. Change byte 0 to 0x12 (Probably you have 0x22)

How do I get this done using OBD11? I have no coding experience.
 

George Ab

Drag Racing Champion
Location
Pacific NW
Ok, so Ive been lurking this thread for a while now. I purchased the 8" DP with the MIB2 brain and usb on my 2015. I have a Fender equipped MK7.

Eurozone sent me an email saying you can make the MIB1 amp work with MIB2 equipment by doing this. Im going to attempt it when my stuff comes in. Here is what they said....

Enabling sound on 2015 vehicles with MIB1 and Fender Audio:
In module 47 in VCDS
1. Plug in VCDS - choose Module 47
2. Choose CODING.
3. Change byte 0 to 0x12 (Probably you have 0x22)

How do I get this done using OBD11? I have no coding experience.


That would be fantastic if it works. I just checked by coding for the MIB1 Fender Amp and it is identical to MIB2 Fender Amp, both have 22.

;SW:5G0-035-456 HW:5G0-035-456 --- Sound System ;Component:MIB_lite_amp H40 0060 Coding:22000000AAAAAA0000

;SW:5Q0-035-456 HW:5Q0-035-456 --- Sound System

;Component:MIB2_lite_amp H20 0130 Coding:2200000000AAAAAA000000000000
 

SargeMKVI

Semper Fi!
Location
Port St.Lucie
Car(s)
2010 GTI
So all you have to do is change the 22 to a 12? I have no clue how to do this,lol. My new equipment will be here next week.

That would be fantastic if it works. I just checked by coding for the MIB1 Fender Amp and it is identical to MIB2 Fender Amp, both have 22.

;SW:5G0-035-456 HW:5G0-035-456 --- Sound System ;Component:MIB_lite_amp H40 0060 Coding:22000000AAAAAA0000

;SW:5Q0-035-456 HW:5Q0-035-456 --- Sound System

;Component:MIB2_lite_amp H20 0130 Coding:2200000000AAAAAA000000000000
 

monsta

Newbie
Location
Kent, UK
Car(s)
Golf GTI Performance
Afaik, Dynaudio (Europe) / Fender (US) can only be activated like this if you get an MIB2 High line unit made by Harmann. The MIB2 Standard units don't work.

Sent from my ONEPLUS A5000 using Tapatalk
 

SargeMKVI

Semper Fi!
Location
Port St.Lucie
Car(s)
2010 GTI
Here is what I found, and it worked.... MIB1 Fender amp works with MIB2 components.
Coding Tweaks Needed

-If you are installing this unit into a 2015 Golf/Golf R/E-Golf/Alltrack/GTI with the MIB1 and Fender Audio, you will need to tweak a setting to enable audio to work with the new Discover Pro.

-To begin make changes into the MIB2 with Vagcom
Manual entry into the GREEN Test Engineering menu to unlock VCDS Diagnosis:
You have to keep pressing the "MENU", until "Service Mode" appears, then press "Test Mode", then press "Green Engineering Menu". After entering the "Green Engineering Menu" to choose the right knob "Enable diagnosis for 10 next boot-ups," wait until you are "In next 10 boot-ups your diagnosis will be available" for out of this press the "nav" on the right side of the display. You must close access to diagnosis after coding is complete.

Enabling sound on 2015 vehicles with MIB1 and Fender Audio:
In module 47 in VCDS
1. Plug in VCDS - choose Module 47
2. Choose CODING.
3. Change byte 0 to 0x12 (Probably you have 0x22)

If Carplay does not work when the MIB2 Discover Pro is installed:
Enter 5F Information Electronics in VCDS

Enter Adaptation-10

Under "Channel 64B", select the channels listed below and make the following changes in the "New Value" Drop down.
IDE03471-ENG130249-Fahrzeugkonfiguration-Apple_DIO: change to "on"
IDE03471-ENG130248-Fahrzeugkonfiguration-Google_GAL: change to "ein"
IDE03471-ENG07590-Fahrzeugkonfiguration-Mirror_link,function_on_hmi_on: change to "on"
IDE10480-MAS10741-Schnittstelle für externen Medien: Aktivierung-Anschluss 1: change to "activated"

Press DO IT to save changes

If "Blue Trainer" parameters do not work correctly
Enabled the “Offroad” in VCDS in the 5F Information Electronics in VCDS. This will cause the accelerometer and steering angle measurements to work

To enable the PDC display if it does not display after the retrofit
You need to have the PDC settings for MIB in two different locations in the adaptation channels.

First the screens :
ENG122227-ENG117496-Car_Function_Adaptations_Gen2-menu_display_pdc,activated
ENG122227-ENG117500-Car_Function_Adaptations_Gen2-menu_display_pdc_after_disclaimer,not activated
ENG122227-ENG117497-Car_Function_Adaptations_Gen2-menu_display_pdc_clamp_15_off,not activated
ENG122227-ENG117498-Car_Function_Adaptations_Gen2-menu_display_pdc_over_threshold_high,activated
ENG122227-ENG117499-Car_Function_Adaptations_Gen2-menu_display_pdc_standstill,not activated

Then the activation :
ENG122229-ENG117710-Car_Function_List_BAP_Gen2-parking_assist_0x0A,activated
ENG122229-ENG117711-Car_Function_List_BAP_Gen2-parking_assist_0x0A_msg_bus,Terminal 15
 

George Ab

Drag Racing Champion
Location
Pacific NW
Here is what I found, and it worked.... MIB1 Fender amp works with MIB2 components.
Coding Tweaks Needed

-If you are installing this unit into a 2015 Golf/Golf R/E-Golf/Alltrack/GTI with the MIB1 and Fender Audio, you will need to tweak a setting to enable audio to work with the new Discover Pro.

-To begin make changes into the MIB2 with Vagcom
Manual entry into the GREEN Test Engineering menu to unlock VCDS Diagnosis:
You have to keep pressing the "MENU", until "Service Mode" appears, then press "Test Mode", then press "Green Engineering Menu". After entering the "Green Engineering Menu" to choose the right knob "Enable diagnosis for 10 next boot-ups," wait until you are "In next 10 boot-ups your diagnosis will be available" for out of this press the "nav" on the right side of the display. You must close access to diagnosis after coding is complete.

Enabling sound on 2015 vehicles with MIB1 and Fender Audio:
In module 47 in VCDS
1. Plug in VCDS - choose Module 47
2. Choose CODING.
3. Change byte 0 to 0x12 (Probably you have 0x22)

If Carplay does not work when the MIB2 Discover Pro is installed:
Enter 5F Information Electronics in VCDS

Enter Adaptation-10

Under "Channel 64B", select the channels listed below and make the following changes in the "New Value" Drop down.
IDE03471-ENG130249-Fahrzeugkonfiguration-Apple_DIO: change to "on"
IDE03471-ENG130248-Fahrzeugkonfiguration-Google_GAL: change to "ein"
IDE03471-ENG07590-Fahrzeugkonfiguration-Mirror_link,function_on_hmi_on: change to "on"
IDE10480-MAS10741-Schnittstelle für externen Medien: Aktivierung-Anschluss 1: change to "activated"


Great work GhostMKVII!!


Updated the original thread with this information in parts and the procedure sections as follows:


IMPORTANT UPDATE: Per this thread a MIB1 amplifier can be made to work with a MIB2 head unit. https://www.golfmk7.com/forums/showp...&postcount=593
 

Rmzhrb

Passed Driver's Ed
Location
NNJ
Here is what I found, and it worked.... MIB1 Fender amp works with MIB2 components.
Coding Tweaks Needed

-If you are installing this unit into a 2015 Golf/Golf R/E-Golf/Alltrack/GTI with the MIB1 and Fender Audio, you will need to tweak a setting to enable audio to work with the new Discover Pro.

-To begin make changes into the MIB2 with Vagcom
Manual entry into the GREEN Test Engineering menu to unlock VCDS Diagnosis:
You have to keep pressing the "MENU", until "Service Mode" appears, then press "Test Mode", then press "Green Engineering Menu". After entering the "Green Engineering Menu" to choose the right knob "Enable diagnosis for 10 next boot-ups," wait until you are "In next 10 boot-ups your diagnosis will be available" for out of this press the "nav" on the right side of the display. You must close access to diagnosis after coding is complete.

Enabling sound on 2015 vehicles with MIB1 and Fender Audio:
In module 47 in VCDS
1. Plug in VCDS - choose Module 47
2. Choose CODING.
3. Change byte 0 to 0x12 (Probably you have 0x22)

If Carplay does not work when the MIB2 Discover Pro is installed:
Enter 5F Information Electronics in VCDS

Enter Adaptation-10

Under "Channel 64B", select the channels listed below and make the following changes in the "New Value" Drop down.
IDE03471-ENG130249-Fahrzeugkonfiguration-Apple_DIO: change to "on"
IDE03471-ENG130248-Fahrzeugkonfiguration-Google_GAL: change to "ein"
IDE03471-ENG07590-Fahrzeugkonfiguration-Mirror_link,function_on_hmi_on: change to "on"
IDE10480-MAS10741-Schnittstelle für externen Medien: Aktivierung-Anschluss 1: change to "activated"

Press DO IT to save changes

If "Blue Trainer" parameters do not work correctly
Enabled the “Offroad” in VCDS in the 5F Information Electronics in VCDS. This will cause the accelerometer and steering angle measurements to work

To enable the PDC display if it does not display after the retrofit
You need to have the PDC settings for MIB in two different locations in the adaptation channels.

First the screens :
ENG122227-ENG117496-Car_Function_Adaptations_Gen2-menu_display_pdc,activated
ENG122227-ENG117500-Car_Function_Adaptations_Gen2-menu_display_pdc_after_disclaimer,not activated
ENG122227-ENG117497-Car_Function_Adaptations_Gen2-menu_display_pdc_clamp_15_off,not activated
ENG122227-ENG117498-Car_Function_Adaptations_Gen2-menu_display_pdc_over_threshold_high,activated
ENG122227-ENG117499-Car_Function_Adaptations_Gen2-menu_display_pdc_standstill,not activated

Then the activation :
ENG122229-ENG117710-Car_Function_List_BAP_Gen2-parking_assist_0x0A,activated
ENG122229-ENG117711-Car_Function_List_BAP_Gen2-parking_assist_0x0A_msg_bus,Terminal 15

That’s great! Now I hope we can find a way to enable navigation and app connect at home too!
 

Cuzoe

Autocross Champion
Location
Los Angeles
trying to change on mib2.5 menu color scheme from blue to red.. anyone knows how ?
IF it's like MIB 2 you will get the red theme by selecting the vehicle type to GTI. From what I remember every other type got the blue theme.

Sent from my ONEPLUS A6013 using Tapatalk
 
Top